Non-Asbestos Fireproof Exterior Wall Panel Price-Friendly Fiber Cement Sheets for Flooring Cement Boards

• Customization: Available
• After-sales Service: Yes
• Warranty: 5 Years
• Model NO.: Cement board
• Type: Non-Asbestos Fiber Cement Board
• Color: Gray
• Thickness: 4.5-30mm
• Raw Material: Cellulose Fiber; Cement, Quartz Powder, Wood Pulp
• Asbestos: 100% Non-Asbestos
• Fire Rating: Class a
• Size: 1220*2440
• Application: Wall Partition, Exterior Wall Cladding, Flooring
• Density: 1.2-1.6g/cm3
• Design Style: Traditional, Modern
• Water Contain: <10%
• Bending Strength: >10 MPa
• Transport Package: Fumigation Wood Pallet + PE Cover + Corner Protect
• Specification: 1220x2440
• Trademark: Sanle
• Origin: China
• HS Code: 68118200
• Production Capacity: 600000 Square Meter/Square Meters Per Month

Product Description

 

Product Description

 

 

Thickness(mm)	Width(mm)	Length(mm)
5-30	1220	2440,3000
Dimensional deviation:
Thickness	≤8mm	±0.3mm
	8--12mm	±0.5mm
	≥12mm	±0.8mm
Width	≤1220mm	±3mm
	>1220mm	±4mm
Length	≤2400mm	±5mm
	>2440mm	±8mm
Physical properties:
Density	1.2-1.6g/cm3
Thermal conductivity	≤0.29 W/(m.k)
Water absorption	≤28%
Water contain	≤10%
Moisture movement	≤0.25%
Bending strength	oven dry	≥16 Mpa
	saturation with water	≥13 Mpa
Non-combustibility	class A
Feature	Waterproof,Fireproof,Moieture proof,Sound insulaton,Flexural strength,Easy installation,etc.

Product Installation

 

1. Fiber cement board preparation: according to the size and design requirements, installing the supporting aluminum accessories( six aluminium accessories per sheet) on the back of fiber cement board ( maximum cross section size is 2780 * 1220 mm). Making cross line according to the vertical distance ( 600 mm ) between the transverse keels and length of fiber cement board uniform size, then fixing supporting aluminum fasteners at the intersection,using 10 mm long and 4 mm thick stainless steel screws.
2. Construction wall preparation: cleaning up the wall surface, and then marking out the position lines and partition lines of the steels according to the design drawings and actual needs.
3. Wire hanging: vertical wire hanging should use the ∮1.0-∮1.2 size steel wire, with 8-10 kgs weight lower counterweight iron, and the upper end is hung on the special wire hanging Angle iron frame. The angle iron frames are fixed on the top corners of the wall with expansion bolts, and marking on the top and bottom of the control line.
4. Keel installation: first fixing 50×50×4 angle iron (with adjustable hole) on the structural surface with ∮8 expansion bolt, that horizontal distance between the angle iron and the 50×50×3.5 vertical square steel tube on the angle steel is 800mm. When installing the vertical square steel tube, it must be checked by hanging steel wire from top to bottom to detect its Perpendicularity. After that, installing the fastening angle iron and the transverse aluminum keel (with 600mm spacing). The connection between angle iron, square steel tube and transverse keel is made with ∮10 bolts. Last, using the infrared level meter to detect whether the horizontal aluminum keel is horizontal, and the steel line to detect whether it is vertical.
5. Fiber cement board installation: mounting the advance processing board on the keel according to the design drawings, and using aluminum accessories to connect the panel and keel. Hanging lightly the same level layer fiber cement boards on the keel, and then adjusting the horizontal and vertical degree of board through upper and lower steel wires. After that, checking the boards seam, whose width should be uniform according to the requirements of design. Last, tightening the stainless steel screws (20mm long and 6mm thick) on the complete set of aluminum accessories.
6. Board joint treatment: using the fiber cement board powder mixing glue to fill the seam, and then painting with special coating twice. When filling the gap, it is necessary to pay attention to the uniform and full filling.


1. The top and bottom keels are fixed respectively top floor and on floor with expansion bolts.
2. The vertical keel should be aligned well according to the requirement (generally being 612 mm) with laterally supporting keel installed.
3. Cutting the board material to the dimensions needed (about 10mm lower than wall height)
4. Board material is fixed on keel in anchoring seam way with tapping screw: the interval of tapping screw is generally about 200~250mm with screws
sinking 0.5mm under the board face.
5. The expansion seam of about 4mm between boards should be kept.
6. The shrouding should be fixed from the middle to the four sides and cannot be operated at multipoint simultaneously to avoid generating inner stress
to make board material bucking.
7. Before board being packaged and fixed, depending the needs, glass cotton or rock cotton can be filled.


Selection of steel structure keel:
1. The span is within 8m: 15H steel for the main beam, #10 channel beam and #63 angle iron for the secondary beam.
2. No embedded parts shall be fixed with expansion bolts.
3. Abundant space can be used upper and lower beam structure, space is not enough can be used plane structure.
Steel structure welding requirements: There are must be at least three sides of the welding, the top surface can not be welded.

Floor board Installation:
1. Before laying the boards, the welding seam on the top surface must be polished flat and the welding spatter must be cleared away.
2. The longitudinal direction of the boards should be parallel to the main beam.
3. Any edge of the board shall not be suspended.
4. A gap of 3-5mm must be left between the boards.
5. The joint between the boards should be located in the center of the beam.

Nailing requirements:
1. Selecting the countersunk head tapping screw, with size of M5*45mm, nailing on the vice-keel (Angle iron).
2. Drill first and then nail, nail hole should be bigger than the diameter of the nail.
3. Nailing starts from the center of the board, and then hits outwards, and finally hits the side nails.
4. The nailing position of the side nail should be about 20mm from the edge of the board.
5. The nail distance is 300-600mm. Treatment of the joint: the joint can be injected with silicone sealant, or mortar can be used.

Follow-up processing:
1. Brushing waterproof coating, and then directly use.
2. Laying wood floor 3.Laying ceramic tiles

Engineering Case

 

Packaging & Shipping

 

Company Introduction

Foshan Jujian Yifang Trading Co., Ltd is a subsidiary of Sanle Building Materials Group. Sanle Building Materials Group is one of the Chinese largest building materials company group, enjoys the well-known Sanle brand at home and abroad. Our group was established in 1998. We are a professional comprehensive building materials group company engaging in the research, development, production, sale and service of fiber cement board, calcium silicate board, EPS cement panel, decorative cement panel and wood grain fiber cement siding panel, gypsum board, MDF board, chipboard, plywood board etc. Our R&D team has more than 20 years R&D production experience. After years development, now we own 4 production bases in China, such as Foshan, Zhaoqing,Hebei and Kunming.

The headquarter of our Sanle Building Materials Group is located in GuangFo Smart Home Mall, Foshan, China. Our group covers more than 220,000 sqm factory area , with 800 workers and more than 10% R & D personals. Advanced technologies, integrated management system, integrated technical criterion, integrated testing procedure, and advanced testing equipment ensure our products with good quality. All of our products are approved by national standards. We offer one-stop service on most of building materials, to save your time and your cost. We insist on the principle of development of 'High quality, Efficiency, Sincerity and Down-to-earth working approach' to provide you with excellent product and service! We sincerely welcome you to visit our company or contact us for cooperation!



Main product
Plywood, MDF board,Particle board,Chip board,Gypsum board,Fiber cement siding board,Non-asbestos cement board, Calcium Silicate Board etc.





FAQ

Q1.What is your terms of packing?
A:Generally,we pack our goods in bundles or wood pallet. We can also do package according to customer's request

Q2.What is your terms of payment?
A:We accept 30% T/T in advance,70% in the period of shipment. Or L/C at sight. 

Q3.What is your terms of delivery?
A:EXW,FOB,CFR.CIF.

Q4.How about your delivery time?
A:For stocks,we can send the goods to loading port within 15 days after receiving your deposit. For production period, it usually needs
about 20 days-25days after receiving the deposit.

Q5.Can you product according to the sample?
A:Yes,we can produce by your samples or technical drawings. We can build the molds and fixtures.

Q6.Do you provide samples for free?
A:We can provide samples for free, but you need to pay for shipping.

The products can meet the national&international environmental standards,and have passed ISO9001:2008,US CARB,SGS,CE
certification, and also we offer OEM services. If you have any other questions.pls feel free to send email to us.